PEAVEY PV1
รหัสสินค้า : PV1
ราคา |
9,980.00 ฿ 24,000.00 ฿ (-58%) |
จำนวนที่จะซื้อ | |
ราคารวม | 9,980.00 ฿ |
สินค้าไม่เพียงพอ
สินค้าหมด
PEAVEY PV1 เพาเวอร์แอมป์ 2 x 250 วัตต์ 8 โอห์ม
เครื่องขยายเสียงเพาเวอร์แอมป์ Peavey PV1 มีกำลังขับ 250 วัตต์ RMS x 2 ที่ 8 Ohms, 410 วัตต์ RMS x 2 ที่ 4 Ohms Class AB Amplifier, Crossover frequencies are fixed at 150 Hz, to drive a 2-Ohm load per channel, Protection indicator, and DDT™ activation on each channel
The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years of amplifier design, this unit takes advantage of rugged TO-3P output devices mounted on massive aluminum extrusions and dissipates heat via an extremely quiet and effective two-speed fan.
PV amplifiers are designed to operate at line voltages as low as 50% of nominal, employing mammoth toroidal power transformers and offering impressive specifications and features not found on similarly priced competitive units. This amp is designed to drive a 2-Ohm load per channel, thus achieving awesome performance levels into 4 Ohms in BRIDGE mode.
PV amplifiers are ruggedly constructed, rack-mountable pieces of gear with superb patching capability, allowing superior flexibility in application. Front panel features include calibrated, detented gain (dB) controls and LED indicators for power (PWR), signal presence (SIG), Thermal Protection indicator, and DDT™ activation on each channel, as well as a rocker mains POWER switch. The back panel contains an IEC connector, line voltage selector switch, dual primary fuses, and the critical cooling fan opening. This opening should have an adequate supply of cool air and should never be blocked or restricted.
Also on the back panel are the input and output sections, including an input barrier strip for permanent installations. Each channel input section includes a combo XLR / TRS phone jack connector, THRU/LOW out and HIGH out TRS jacks, and activation switches for the LOW CUT filter and crossover (150 Hz XOVER). Channel output sections feature dual shock-proof binding posts and four-conductor twist lock connectors. An additional four-conductor twist lock connector allows BRIDGE mode output.
Features
- Stereo Mode 4 Ohms, 1 Khz, 1% Thd 410 W Rms/Chan
- Input Sensitivity & Impedance: @ Rated Output Power, 4 Ohms 1.08 V Rms / 2.87dbu
- Frequency Response: Stereo Mode, Both Channels Driven +0, -2db At 1 Watt
- Power Consumption: Stereo Mode, Both Channels Driven @ 1/8 Rated Output Power, 4 Ohms 450w
- Topology Class Ab
Specifications
RATED OUTPUT POWER @ 120V AC Line:
Stereo mode
4 Ohms, 1 kHz, 1% THD
410 W RMS/chan
8 Ohms, 1 kHz, 1% THD
250 W RMS/chan
Bridge mode, mono 8 Ohms, 1 kHz, 1% THD
760 W RMS
HUM & NOISE
“A” weighted, reference to rated power @ 8ohms
INPUT SENSITIVITY & IMPEDANCE
@ rated output power, 4 ohms
1.08 V RMS / 2.87dBu
Balanced, TRS 1/4” phone jack
10 K Ohms per leg
Balanced, XLR (pin 2 positive)
10 K Ohms per leg
Overall system gain per channel
40X (+32 dB)
DISTORTION (THD, typical value)
Stereo mode, both channels driven, 4 Ohms
20 Hz to 20 kHz, 10 dB below rated power
20 Hz to 2 kHz, at full rated power
FREQUENCY RESPONSE
Stereo mode, both channels driven +0, -2dB at 1 Watt
DAMPING FACTOR: (Typical value)
Stereo mode, both channels driven
8 Ohms, 20 Hz – 2 kHz
POWER CONSUMPTION:
Stereo mode, both channels driven @ 1/8 rated output power, 4 Ohms
450W
TOPOLOGY
Class AB
WEIGHT
40 lbs (18.2 kg)